您好,欢迎来到济南通宇恒成自动化工程有限公司网站!

服务热线

当前位置: 首页- 新闻中心 > 公司动态
常见问题
新闻中心

螺丝拧在边上就变形?先看骨架是不是“九折型材”

发布时间:2026-10-30 来源:http://www.tongyuhengcheng.com/ 浏览量:

很多自控柜、PLC柜、变频柜现场一开门,门板往下坠、侧板受点力就凹进去。业主第一反应是“钣金太薄”,其实薄不薄是次要,骨架怎么拼才是根本。

Many automatic control cabinets, PLC cabinets, and frequency conversion cabinets have door panels falling down and side panels sinking in when they are subjected to some force on site. The first reaction of the owner is that the sheet metal is too thin. In fact, whether it is thin or not is secondary, and how to assemble the skeleton is fundamental.

微信图片_202009081137222

普通机柜用整张钢板折边焊成方框,成本低,但受力全压在焊角和螺钉上。仿威图体系的核心是九折型材框架——一根型材有九个折弯面,拼成柜体后每一面大多能分担载荷,不用全靠焊点硬扛。

A regular cabinet is made of a whole steel plate folded and welded into a box, which has low cost, but the force is fully pressed on the welding corners and screws. The core of the imitation Weitu system is the nine fold profile frame - one profile has nine bending surfaces, and each surface can share the load after being assembled into the cabinet, without relying solely on welding points for hard support.

挑的时候盯四件事,比听“德国工艺”四个字管用:

When choosing, focus on four things, which are more effective than listening to the four words' German craftsmanship ':

型材是真九折还是假九折。真型材截面能看到连续的九个折边,壁厚2.0到2.5mm;有些厂用“四折型材+补强板”冒充,外观差不多,承重差一截。让厂家切一段边角料给你看截面。

Is the profile genuine or fake at a 10% discount. The cross-section of the real profile can see nine continuous folded edges with a wall thickness of 2.0 to 2.5mm; some factories use "four fold profiles+reinforcing plates" to impersonate it, with similar appearance but a difference in load-bearing capacity. Ask the manufacturer to cut a piece of corner material to show you the cross-section.

安装梁可调。仿威图的价值一半在“灵活”——横梁、竖梁带模数孔,PLC、变频器、导轨上下左右随便移。买回来发现孔距不对、梁焊死不能动,等于花了仿威图的钱买了个焊接柜。

The installation beam is adjustable. Half of the value of the imitation Weitu lies in its "flexibility" - horizontal and vertical beams with modular holes, PLC、 The frequency converter and guide rail can be moved up, down, left, and right freely. When I bought it, I found that the hole spacing was incorrect and the beam was welded dead and couldn't be moved, which is equivalent to spending money on a welding cabinet imitating Weitu.

门轴和结构。单门、双门、玻璃门、背板可拆,这些不是选配是基本功。门铰链用暗铰,开角110度以上,频繁检修不碍事。门缝均匀度靠骨架精度,不靠后期掰。

Door axis and structure. Single door, double door, glass door, and detachable back panel are not optional but basic features. The door hinges are concealed hinges with an opening angle of over 110 degrees, and frequent maintenance is not a problem. The uniformity of the door seam depends on the accuracy of the skeleton, not on later bending.

防护和密封。IP55不是刷漆刷出来的。门框一圈聚氨酯发泡胶条、底部进线口配敲落孔和电缆葛兰头、顶板可装排风扇和滤网。户外柜还要看顶盖防雨檐和底座抬高。

Protection and sealing. IP55 is not made by brushing paint. The door frame is covered with a polyurethane foam strip, the bottom inlet is equipped with knock off holes and cable gland heads, and the top plate can be equipped with exhaust fans and filters. Outdoor cabinets also need to consider the top cover, rain proof eaves, and raised base.

再顺手核三条车间里非常容易漏的:

The most easily leaked items in the three workshops are:

表面处理:静电喷塑膜厚60到80微米,盐雾试验报告拿出来看,别信“户外专用漆”口头承诺。

Surface treatment: The thickness of the electrostatic spray film is 60 to 80 microns. Take out the salt spray test report and don't believe the verbal promise of "outdoor special paint".

接地:柜门和骨架之间建议有黄绿接地线或接地爪,不然门一开就悬空,漏电保护形同虚设。

Grounding: There must be a yellow green grounding wire or grounding claw between the cabinet door and the frame, otherwise the door will be suspended when opened, and the leakage protection will be ineffective.

内部件兼容性:导轨用顶丝还是卡扣、线槽留多宽、变频器散热风道朝哪开,这些在画图阶段定好,别等电气接线时才发现散热器顶到侧板。

Internal compatibility: Whether to use top screws or buckles for guide rails, how wide to leave wire slots, and which direction to open the inverter cooling air duct should be determined during the drawing stage. Don't wait until electrical wiring to discover that the radiator is on top of the side panel.

顺手一条红线:仿威图柜不是“长得像威图”。型材模具、模数孔距、配件体系这三样对不上原厂标准的,后期加个风扇、换个门锁都要自己打孔,省下的差价全变成钳工工时。

A casual red line: Imitating a Weitu cabinet is not "looking like a Weitu". If the profile mold, modular hole spacing, and accessory system do not meet the original factory standards, you will have to drill your own holes to add a fan or replace a door lock in the later stage, saving all the price difference and turning it into fitter hours.

把“九折型材看截面、安装梁要可调、胶条门轴别省、模数兼容先画图”这四句钉在采购技术协议里,这台柜子用十年门不坠、漆不爆,才对得起“仿威图”三个字。

Nail the four sentences of "nine fold profile to see the section, adjustable installation beam, saved rubber strip door axis, and compatible module to draw first" into the procurement technical agreement. This cabinet will last for ten years without the door falling or the paint bursting, which is worthy of the three words "imitation Weitu".

首页首页 产品产品 电话电话 置顶置顶