机箱机柜的品质直接受制作工艺的好坏的影响，工艺较不错机箱的钢板边缘不会泛起毛边、锐口、毛刺等现象，并且裸露的边角都经由折边处理，不易划伤装机者的手。各个插卡槽位的定位也都相称，不会泛起配件装置不上或许错位的为难状况。

　　The quality of the chassis and cabinet is directly affected by the quality of the manufacturing process. If the process is good, the steel plate edges of the chassis will not have burrs, sharp edges, burrs, etc., and the exposed corners are all folded to prevent scratching the hands of the installer. The positioning of each card slot is also appropriate, so there will be no difficult situation of accessory devices not being installed or misplaced.

　　那么怎么选购机箱机柜呢？

　　So how to choose a chassis cabinet?

　　01

　　01

　　看架构布局

　　View architecture layout

　　一般来说，挡板要多，而且具有散热孔，一些用来固定线缆的铁皮要包边，防预损坏线缆。侧壁风扇应装置在机柜后壁，由于设备后部产生大多数的热量。

　　Generally speaking, there should be more baffles with heat dissipation holes, and some iron sheets used to fix cables should be wrapped to prevent pre damage to the cables. The side wall fan should be installed on the back wall of the cabinet, as most of the heat is generated at the rear of the equipment.

　　02

　　02

　　看功用

　　See function

　　先考虑的应是稳定性。

　　The first consideration should be stability.

　　03

　　03

　　看材料

　　Look at the materials

　　要挑选钣金机箱机柜，一起钢板改成要厚，你用手指敲一下，就能感觉到哪些厚哪些薄了。它坚实的外壳保护着板卡、电源及存储设备，能防压、防冲击、防尘，并且它还能发挥防电磁搅扰、辐射的功用，起屏蔽电磁辐射的效果。再次，它还提供了许多便于运用的面板开关指示灯等，让操作者愈方便地操作微机或观察微机的运行状况。

　　To choose a sheet metal chassis cabinet, change the steel plate together to make it thicker. You can feel which ones are thicker and which ones are thinner by tapping with your fingers. Its solid shell protects the board, power supply, and storage devices, and can prevent pressure, impact, and dust. It can also play a role in preventing electromagnetic interference and radiation, and has the effect of shielding electromagnetic radiation. Again, it also provides many user-friendly panel switches, indicator lights, etc., making it more convenient for operators to operate or observe the operation status of the microcomputer.

　　04

　　看喷漆

　　Look at the spray paint

　　一个合格的机柜，所有的钢材都需求喷漆，而且喷漆改成要平均，这样才能良好地防锈、防尘等。

　　A qualified cabinet requires all steel to be painted, and the painting should be evenly distributed to ensure good rust and dust prevention.

　　05

　　看散热

　　Check the heat dissipation

　　估计一下你的设备发热量有多大，一般来说，柜顶都有二到四个风扇，风扇都是多多益善的啦。还有一些用来固定机架的螺丝、螺母等，也要足量。不因日后扩展而带来配件不足的麻烦。

　　Estimate how much heat your device generates. Generally speaking, there are two to four fans on the top of the cabinet, and the more fans there are, the better. There are also some screws, nuts, etc. used to fix the rack, which should be sufficient. Not causing the trouble of insufficient accessories due to future expansion.

　　06

　　看配件

　　Check the accessories

　　由于装置中包含网络电缆、电信电缆和电源电缆，需求购买钩环带或带齿的带子来地把电缆有序的固定在机柜里面。假设机柜带有电缆管理模块使电缆能够直接固定在笔直装置轨内，则再好不过。

　　Due to the inclusion of network cables, telecommunications cables, and power cables in the device, it is necessary to purchase hook and loop or toothed straps to orderly secure the cables inside the cabinet. It would be great if the cabinet had a cable management module that allows cables to be directly fixed in the straight device track.

　　07

　　看玻璃

　　Look at the glass

　　玻璃改成要厚一点的，还要留意玻璃的周边是否有裂缝，假设有裂缝，就意味着有隐患了，还有要留意是否棘手。

　　Make the glass thicker and pay attention to whether there are cracks around the glass. If there are cracks, it means there are hidden dangers. Also, pay attention to whether it is difficult.

　　在散热技术方面，机箱机柜设备降温多数选用空调系统推送冷气的方式，为了局部高热去降温整个空调系统的温度往往将很低，提升电力机箱机柜的使用率。

　　In terms of heat dissipation technology, the cooling of chassis and cabinet equipment is mostly achieved by using air conditioning systems to push cold air. In order to reduce the temperature of the entire air conditioning system due to local high heat, the temperature is often lowered to a very low level, thereby improving the utilization rate of power chassis and cabinets.

　　便于制造

　　Easy to manufacture

　　01在同时达到技术要求的的基础上，应依据各企业的现实生产，优先考虑制作工艺简便的钣金加工方法，以降低成本，提升生产速率。

　　01On the basis of meeting technical requirements simultaneously, priority should be given to sheet metal processing methods with simple manufacturing processes based on the actual production of each enterprise, in order to reduce costs and improve production rates.

　　尽量减少焊接

　　Minimize welding as much as possible

　　02 焊接后会引起变形，而且焊接外表料理不标致，波及生产速率，另外能够改变工艺来替代焊接。1、利用铆接来替代焊接，在节约时间的同时又能不变形。2、用冲压来代替焊接，不宜变形，但有时要利用简易模具。3、取消作用不大的焊接。对于受力小或仅起链接作用的焊缝，可采用间接断焊来代替延续焊。压铆过程示意图

　　Welding can cause deformation, and the welding surface is not aesthetically pleasing, affecting production speed. In addition, the process can be changed to replace welding. 1. Using riveting instead of welding can save time while avoiding deformation. 2. Using stamping instead of welding should not cause deformation, but sometimes simple molds should be used. 3. Cancel welding that has little effect. For welds with low stress or only serving as a link, indirect break welding can be used instead of continuous welding. Schematic diagram of riveting process

　　取材要正确，冷作钣金的原材按材质分，有合金构造钢，碳素构造钢，铝铜等。按轧制的断面形状特征分，有型材，板材，线材，型材。在挑选时应按以下几点正确挑选：

　　The material selection should be correct. The raw materials for cold sheet metal are classified according to their materials, including alloy structural steel, carbon structural steel, aluminum copper, etc. According to the characteristics of the cross-sectional shape of rolling, there are profiles, plates, wires, and profiles. When selecting, the following points should be followed correctly:

　　03 1、提供原材料的利用率钣金加工，在强度和技术要求的前提下，其胚料允诺以小拼大，这样能够减少边角余料，降低成本，依据板材的大小，能够选用订好的尺寸长度的板材。2、依据工作情况正确挑取材料钣金加工设计的活泛性大，具有许多的优良性冷作件的壁厚能够相差很大，按受力情况不同和工作情况的不同，可选用不同强度、不同、等性能的材料。3、尽量采用轧制的型材经轧制的型材，尺寸较准确，品质，外表平整，光润，价钱低，采用轧制的型材还能够减少焊接及成型加工开销，具率不错，成本还行的优点，所以在构造件中能普遍的应用。

　　03 1. Provide the utilization rate of raw materials for sheet metal processing. Under the premise of strength and technical requirements, the raw materials are promised to be assembled in small sizes to reduce corner scraps and lower costs. Based on the size of the sheet metal, it is possible to select sheets of predetermined size and length. 2. The flexibility of selecting materials correctly based on work conditions in sheet metal processing design is high, and it has many excellent properties. The wall thickness of cold work parts can vary greatly, and materials with different strengths, properties, etc. can be selected according to different stress conditions and work conditions. 3. Try to use rolled profiles as much as possible. Rolled profiles have accurate dimensions, good quality, smooth appearance, and low price. Using rolled profiles can also reduce welding and forming processing costs, with good yield and reasonable cost. Therefore, they can be widely used in structural components.

　　本文由  济南机箱机柜 友情奉献.更多有关的知识请点击  http://www.tongyuhengcheng.com/   真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Jinan Chassis Cabinet For more related knowledge, please click http://www.tongyuhengcheng.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.