一、前言

　　1、 Preface

　　机箱机柜作为重要的供电节点，在使用中有着严格的要求，在安装时也非常重要，而扭力的选择是非常重要的一项。然而，在实际操作中，如何选择合适的扭矩成了让许多人疑惑的问题。因此，本文提供了一份机箱机柜螺丝扭力标准参照表，帮助读者选择合适的扭力，确保安装的稳固性和可靠性。

　　As an important power supply node, the chassis cabinet has strict requirements in use and installation, and the selection of torque is also very important. However, in practical operation, how to choose the appropriate torque has become a question that many people are puzzled about. Therefore, this article provides a reference table for the torque standards of chassis cabinet screws, helping readers choose the appropriate torque to ensure the stability and reliability of installation.

　　二、机箱机柜螺丝扭力标准参照表以下为常见机箱机柜螺丝通用的扭力需求，供参考。

　　2、 The torque standards for chassis and cabinet screws refer to the table below for common torque requirements for chassis and cabinet screws, for reference only.

　　1、M4螺丝需要6-7牛米的扭矩；

　　1. M4 screws require a torque of 6-7 Nm;

　　2、M5螺丝需要10-12牛米的扭矩；

　　2. M5 screws require a torque of 10-12 Nm;

　　3、M6螺丝需要20-23牛米的扭矩；

　　3. M6 screws require a torque of 20-23 Nm;

　　4、M8螺丝需要40-50牛米的扭矩；

　　4. M8 screws require a torque of 40-50 Nm;

　　5、M10螺丝需要70-80牛米的扭矩。当然，具体的扭力选用还要根据不同的情况来选择，如螺栓的长度、松紧程度等，需要根据实际情况进行调整。

　　5. M10 screws require a torque of 70-80 Nm. Of course, the specific torque selection also depends on different situations, such as the length and tightness of bolts, which need to be adjusted according to the actual situation.

　　三、如何选择扭力在日常操作中，我们有以下几种方法来选择合适的扭力。

　　3、 How to choose the appropriate torque in daily operation? We have the following methods to choose the appropriate torque.

　　1、手感法：即通过手感来判断。

　　1. Texture method: It is judged by the texture of the hand.

　　2、使用扭矩扳手：机箱机柜螺丝使用扭矩扳手来旋紧，选择合适的扭力。

　　2. Use a torque wrench: Use a torque wrench to tighten the screws of the chassis and cabinet, and choose the appropriate torque.

　　3、数值法：根据相关资料提供的标准来选择扭力。使用扭矩扳手进行操作，因为它可以提供更加准确的扭力，可以避免意外情况的出现。

　　3. Numerical method: Select torque based on the standards provided by relevant information. It is recommended to use a torque wrench for operation, as it can provide more accurate torque and avoid unexpected situations.

　　四、注意事项在实际操作中，需要注意以下几点：

　　4、 In practical operation, the following points need to be noted:

　　1、螺栓的长度：如果螺栓过长，需要加宽扭力范围。

　　1. Bolt length: If the bolt is too long, the torque range needs to be widened.

　　2、不要超过扭力限制：我们需要根据机箱机柜螺丝扭力标准参照表来选择合适的扭力，而不应该超出扭力限制，这样会导致螺丝断裂或者松动。

　　2. Do not exceed the torque limit: We need to refer to the torque standard table for chassis and cabinet screws to choose the appropriate torque, and should not exceed the torque limit, which may cause screws to break or loosen.

　　3、正确的顺序：在进行螺丝旋紧的时候，需要按照规定顺序来操作，否则会引起不必要的问题。

　　3. Correct sequence: When tightening screws, it is necessary to follow the prescribed sequence, otherwise it may cause unnecessary problems.

　　5、总结选择合适的螺丝扭力对于安装稳固的机箱机柜来说关重要，需要根据实际情况来进行选择。本文提供了机箱机柜螺丝扭力标准参照表，希望能够帮助读者更好地理解和应用扭力。

　　5. Choosing the appropriate screw torque is crucial for installing a stable chassis cabinet, and the selection should be based on the actual situation. This article provides a reference table for the torque standards of chassis and cabinet screws, hoping to help readers better understand and apply torque.

　　本文由 济南机箱机柜   友情奉献.更多有关的知识请点击  http://www.huannengpower.com/   真诚的态度.为您提供为的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.

　　This article is a friendly contribution from Jinan Chassis Cabinet For more related knowledge, please click http://www.huannengpower.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.