您好,欢迎来到济南通宇恒成自动化工程有限公司网站!

服务热线

当前位置: 首页- 新闻中心 > 业内资讯
常见问题
新闻中心

机柜并柜之后门关不严,问题出在型材上

发布时间:2026-10-12 来源:http://www.tongyuhengcheng.com/ 浏览量:

成套厂采购仿威图机柜,单台看样品没问题,门开关顺畅,密封条贴合。但几台柜子并排拼在一起之后,中间那几台的门开始关不严,密封条压不实,防护等级从IP54掉到IP20都不到。排查下来,不是门板变形,是框架型材的截面精度不够。

The complete set factory purchases imitation Weitu cabinets, and there are no problems with individual samples. The door opening and closing are smooth, and the sealing strip is tightly attached. But after several cabinets were put together side by side, the doors of the middle ones began to fail to close tightly, the sealing strips were not pressed tightly, and the protection level dropped from IP54 to IP20. After investigation, it was found that the deformation was not caused by the door panel, but by the insufficient cross-sectional accuracy of the frame profile.

微信图片_202009081137222

九折型材是仿威图的核心,不是外形像就行。

The nine fold profile is the core of the imitation Weitu, not just the appearance.

威图机柜的灵魂在于它的九折型材——截面经过九次折弯,形成复杂的几何形状,在同样板材厚度下获得更高的抗弯和抗扭强度。这套型材的安装孔距、折弯角度、截面尺寸都有严格标准。并柜时,相邻机柜的框架通过连接件固定,如果型材的截面精度不够,折弯角度有偏差,两台柜子拼在一起就会出现“内八字”或“外八字”——中间的门框距离比两端窄,门板装上去自然关不严。

The soul of the Weitu cabinet lies in its nine fold profile - the cross-section undergoes nine bends to form complex geometric shapes, achieving higher bending and torsional strength at the same plate thickness. The installation hole spacing, bending angle, and cross-sectional dimensions of this profile have strict standards. When merging cabinets, the frames of adjacent cabinets are fixed by connecting pieces. If the cross-sectional accuracy of the profiles is not sufficient and there is a deviation in the bending angle, two cabinets assembled together will have an "inner eight" or "outer eight" shape - the distance between the middle door frame is narrower than the two ends, and the door panel will naturally not close tightly when installed.

框架壁厚,是低价仿制品非常先缩水的地方。

The thickness of the frame wall is the first place where low-priced imitations shrink.

威图原厂机柜的框架板材通常在1.5-2.0mm之间,部分低价仿制品降到1.0-1.2mm。壁厚不够,框架的刚性不足,装上断路器、变频器这些重型元件后,柜体会轻微变形。单台柜子看不出来,几台并柜之后变形累积,门框的平面度超差,门就关不上了。山东本地成套厂的经验是:拿卡尺量框架立柱的壁厚,低于1.5mm的,承载能力就要打问号。

The frame plate of the original Weitu cabinet is usually between 1.5-2.0mm, and some low-priced imitations have reduced it to 1.0-1.2mm. The wall thickness is not enough, and the rigidity of the frame is insufficient. After installing heavy components such as circuit breakers and frequency converters, the cabinet will deform slightly. A single cabinet cannot be seen, and after several cabinets are combined, deformation accumulates, and the flatness of the door frame exceeds the tolerance, causing the door to not close. The experience of a local complete set factory in Shandong is to measure the wall thickness of the frame column with a caliper. If it is less than 1.5mm, the bearing capacity should be questioned.

并柜连接件的质量,同样影响整体刚性。

The quality of the cabinet connecting components also affects the overall rigidity.

仿威图机柜的并柜连接件,如果是薄铁皮冲压的,拧紧螺栓后变形,两台柜子之间就有缝隙。正规的连接件应该是厚钢板加工,螺栓孔位准确,拧紧后能把两台柜子牢牢锁在一起,整体刚性接近一台大柜子。采购时要问清楚连接件的材质和厚度,别只看机柜主体。

If the parallel connection of the imitation Weitu cabinet is made of thin iron sheet stamping, it will deform after tightening the bolts, and there will be gaps between the two cabinets. A formal connector should be made of thick steel plate, with precise bolt hole positions. After tightening, it can firmly lock two cabinets together, and the overall rigidity is close to that of a large cabinet. When purchasing, it is important to clarify the material and thickness of the connectors, not just the main body of the cabinet.

门锁和铰链的位置精度,决定门能不能关严。

The positional accuracy of door locks and hinges determines whether the door can be tightly closed.

仿威图机柜的门通常用多点锁,上下各一个锁点。如果框架上的锁孔位置精度不够,锁舌对不上锁孔,门就关不严。铰链的安装位置同样关键——铰链偏了,门板在关闭时会翘起一个角。这些问题在单台组装时可能被掩盖,并柜之后因为框架受应力,全部暴露出来。

The doors of imitation Weitu cabinets usually use multi-point locks, with one locking point on each side. If the accuracy of the lock hole position on the frame is not sufficient, the lock tongue cannot match the lock hole, and the door cannot be closed tightly. The installation position of the hinge is also crucial - if the hinge is off center, the door panel will tilt at an angle when closed. These issues may be concealed during single unit assembly and fully exposed after cabinet assembly due to frame stress.

通宇恒成这类本地厂家,优势在配套和响应。

Local manufacturers like Tongyu Hengcheng have advantages in supporting and responding.

仿威图机柜不是孤立的产品,需要和MNS抽屉柜、操作台、配电箱配套使用。本地厂家能提供从机柜到成套配件的一站式供应,并柜时连接件、锁具、密封条都匹配,现场安装问题少。出了质量问题,本地厂家响应快,不用等外地发货。这也是山东机箱机柜产业集群的优势——配套齐全、响应及时。

The imitation Weitu cabinet is not an isolated product and needs to be used in conjunction with MNS drawer cabinets, operation consoles, and distribution boxes. Local manufacturers can provide one-stop supply from cabinets to complete sets of accessories, with matching connectors, locks, and sealing strips during cabinet consolidation, resulting in fewer on-site installation issues. If there is a quality issue, the local manufacturer responds quickly and there is no need to wait for shipments from other places. This is also the advantage of the Shandong chassis and cabinet industry cluster - complete supporting facilities and timely response.

仿威图机柜的选型逻辑很清晰:确认九折型材的截面精度和孔距标准,卡尺量框架壁厚不低于1.5mm,检查并柜连接件的材质和厚度,确认门锁和铰链的安装精度。外形像只是入门,型材精度才决定并柜之后能不能用。

The selection logic of the imitation Weitu cabinet is very clear: confirm the cross-sectional accuracy and hole spacing standards of the nine fold profile, measure the frame wall thickness with a caliper not less than 1.5mm, check the material and thickness of the cabinet connection, and confirm the installation accuracy of the door lock and hinge. The appearance is just an entry-level, and the accuracy of the profile determines whether it can be used after cabinet consolidation.

首页首页 产品产品 电话电话 置顶置顶