您好,欢迎来到济南通宇恒成自动化工程有限公司网站!

服务热线

当前位置: 首页- 新闻中心 > 公司动态
常见问题
新闻中心

订货单先锁“看不见的”

发布时间:2026-11-14 来源:http://www.tongyuhengcheng.com/ 浏览量:

山东做电气成套的厂不少,济南本地就有集群。项目采购时容易陷进比价:同叫MNS、同叫仿威图,报价能差出一大截。差价不在外观,在订货单没锁死的“不可见部位”。

There are many factories in Shandong that produce complete electrical sets, and there is a cluster in Jinan. It is easy to get caught up in price comparisons during project procurement: both called MNS and imitation Weitu, the quotation can differ significantly. The price difference is not in the appearance, but in the "invisible parts" that are not locked in the purchase order.

先分柜型,不盲目上抽屉

Separate cabinet types first, do not blindly add drawers

8

回路固定、泵房照明、小容量配电:GGD固定柜够用,别硬上抽屉柜花冤枉钱;

Fixed circuit, pump room lighting, small capacity power distribution: GGD fixed cabinet is sufficient, don't waste money on hard drawer cabinets;

产线常改回路、连续生产、停机代价高:MNS/抽屉柜值,坏一路抽换一路,有备用抽屉十分钟恢复;

Frequent circuit changes, continuous production, and high downtime costs on the production line: MNS/drawer cabinet value, one damaged circuit can be replaced, and spare drawers can be restored in ten minutes;

自动化产线、PLC/变频/伺服集中:仿威图PS柜+PLC柜组合,看型材和散热;

Automated production line, PLC/frequency conversion/servo centralization: imitating Weitu PS cabinet+PLC cabinet combination, observing profiles and heat dissipation;

户外/腐蚀环境:不锈钢柜体+IP65以上,密封条一体发泡。

Outdoor/Corrosive Environment: Stainless steel cabinet with IP65 or higher rating, with integrated foam sealing strip.

订货前把这张表写进技术协议

Write this form into the technical agreement before placing an order

主母线:材质T2铜、截面(如100×10)、镀锡/镀银、温升试验值;

Main busbar: material T2 copper, cross-section (such as 100 × 10), tin/silver plating, temperature rise test value;

短路参数:Icw短时耐受、分断能力按变压器出口预期电流算,不按样本下限选(常见50kA以上);

Short circuit parameters: Icw short-term withstand and breaking capacity are calculated based on the expected current at the transformer outlet, not selected according to the lower limit of the sample (usually above 50kA);

抽屉模数:8E/4、8E/2、8E、16E留20%备用单元,别塞满;

Drawer module: 20% spare units are reserved for 8E/4, 8E/2, 8E, 16E, do not fill them up;

环境降容:配电室超35℃、变频集中,载流量按0.7–0.8系数留余量;

Environmental capacity reduction: When the temperature in the distribution room exceeds 35 ℃ and the frequency conversion is concentrated, a margin of 0.7-0.8 coefficient is reserved for the current carrying capacity;

板材壁厚:框架立柱≥1.5mm(原厂威图系1.5–2.0mm),门板≥1.5mm,拿卡尺验收;

Board wall thickness: frame columns ≥ 1.5mm (original Weitu series 1.5-2.0mm), door panels ≥ 1.5mm, inspected with a caliper;

防护等级:标IP54不算数,看发泡密封条压缩均匀性、锁点分布、并柜后门缝;

Protection level: The standard IP54 does not count. Check the compression uniformity of the foam sealing strip, the distribution of locking points, and the door gap after cabinet merging;

通讯协议:RS485/Modbus/Profinet提前定,避免后期加网关。

Communication protocol: RS485/Modbus/Profinet pre-set to avoid adding a gateway later.

柜内工艺盯三道坎

Pay attention to the three obstacles in the cabinet process

一次回路:铜排搭接面搪锡、力矩紧固、相序色标、PE独立排,黄绿线不混用;

Primary circuit: Copper bar overlapping surface tinned, torque tightened, phase sequence color code, PE independent row, yellow and green wires not mixed;

二次回路:线号两端一一对应,控制线≥0.75mm²,电流回路≥2.5mm²,预留15%备用端子;

Secondary circuit: The wire numbers correspond one-to-one at both ends, the control wire is ≥ 0.75mm ², the current circuit is ≥ 2.5mm ², and 15% spare terminals are reserved;

强弱电分离:动力与4–20mA屏蔽线分槽,间距≥30cm,屏蔽层单端接PE,不两端接地。

Separation of strong and weak electricity: The power and 4-20mA shielded wires are separated into slots with a spacing of ≥ 30cm. The shielding layer is connected to PE at one end and not grounded at both ends.

厂家能力看“自有产线”而不是展厅

Manufacturer's ability depends on 'own production line' rather than exhibition hall

激光切割、数控折弯、焊接、喷涂是否自主管控,外协多的柜体一致性难控;

Whether laser cutting, CNC bending, welding, and spraying are independently controlled, and the consistency of outsourced cabinets is difficult to control;

九折型材截面精度:并柜后门缝均匀、不变形,才是真仿威图结构;

The accuracy of the cross-section of the nine fold profile: the uniform and non deformed rear door seam after cabinet merging is the true imitation of the Weitu structure;

CCC/GB 7251.1-2023体系、出厂FAT(绝缘、耐压、温升、机械操作)报告随货;

CCC/GB 7251.1-2023 system, factory FAT (insulation, withstand voltage, temperature rise, mechanical operation) report accompanying the shipment;

元器件清单可溯源,ABB/施耐德/正泰/天正别混用替代不告知。

The list of components can be traced, but ABB/Schneider/Chint/Tianzhengbie are mixed and replaced without informing.

现场验收动三下

Three rounds of on-site acceptance inspection

卡尺量铜排截面和板材壁厚;

Measure the cross-section of the copper bar and the wall thickness of the plate with a caliper;

核对型式试验报告编号与证书覆盖范围;

Verify the type test report number and certificate coverage;

做绝缘(二次≥1MΩ)和耐压试验,带负荷试运行看温升。

Perform insulation (secondary ≥ 1M Ω) and withstand voltage tests, and perform load testing to observe temperature rise.

电气成套的本质,不是“铁壳子里塞电器”,是把“载流—保护—控制—散热—可维护”焊进一张订货单。报价单上省掉的不可见部位,三年后全变成停电检修单。

The essence of an electrical complete set is not to "plug electrical appliances into an iron shell", but to weld "current carrying protection control heat dissipation maintainability" into one purchase order. The invisible parts omitted from the quotation will all become power outage maintenance orders after three years.

首页首页 产品产品 电话电话 置顶置顶